Flowback water
From Wikimarcellus
| Revision as of 01:57, 24 July 2010 Tcopley (Talk | contribs) ← Previous diff |
Revision as of 21:15, 24 October 2010 Tcopley (Talk | contribs) Next diff → |
||
| Line 1: | Line 1: | ||
| - | In the Marcellus shale, ''flowback water'' (aka ''backflow water'') from [[Hydro-fracturing|fracing]] natgas wells, consists of the [[Drilling fluid|frac fluid]] which returns to the surface (aka the ''frac load recovery'') and [[produced water]]. | + | ''Flowback water'' (aka ''backflow water'') is the murky, salty water from [[Hydro-fracturing|fracing]] natural gas wells. It consists of the [[Drilling fluid|frac fluid]] which returns to the surface (aka the ''frac load recovery'') as well as [[produced water]]. |
| The frac load recovery can be anywhere from 20-40% percent of the volume of fluid that is forced down a well, and it flows back over a period of 3-4 weeks after fracing. More than half of the frac fluid remains in the formation. At a certain point there is a transition between primarily recovering frac fluid to that of [[produced water]]. Usually this point is difficult to distinguish, yet may be discerned from the different chemical signatures of the frac water versus the naturally occurring water produced by the formation. A typical flowback of drilling fluids might run 40,000 bbl. After the initial 3-4 week post-fracing recovery of drilling fluids, an additional 10,000 to 30,000 bbl of produced water may flow for up to two years. | The frac load recovery can be anywhere from 20-40% percent of the volume of fluid that is forced down a well, and it flows back over a period of 3-4 weeks after fracing. More than half of the frac fluid remains in the formation. At a certain point there is a transition between primarily recovering frac fluid to that of [[produced water]]. Usually this point is difficult to distinguish, yet may be discerned from the different chemical signatures of the frac water versus the naturally occurring water produced by the formation. A typical flowback of drilling fluids might run 40,000 bbl. After the initial 3-4 week post-fracing recovery of drilling fluids, an additional 10,000 to 30,000 bbl of produced water may flow for up to two years. | ||
Revision as of 21:15, 24 October 2010
Flowback water (aka backflow water) is the murky, salty water from fracing natural gas wells. It consists of the frac fluid which returns to the surface (aka the frac load recovery) as well as produced water.
The frac load recovery can be anywhere from 20-40% percent of the volume of fluid that is forced down a well, and it flows back over a period of 3-4 weeks after fracing. More than half of the frac fluid remains in the formation. At a certain point there is a transition between primarily recovering frac fluid to that of produced water. Usually this point is difficult to distinguish, yet may be discerned from the different chemical signatures of the frac water versus the naturally occurring water produced by the formation. A typical flowback of drilling fluids might run 40,000 bbl. After the initial 3-4 week post-fracing recovery of drilling fluids, an additional 10,000 to 30,000 bbl of produced water may flow for up to two years.
Flowback water may be characterized as having high salinity and total dissolved solids (TDS). It is laden with the same fracing chemicals that were pumped into the well, in addition to any unique contaminants that are present in the rock formation water deep below. In addition to natural salinity of water in the formation, any fresh water that is forced down a well when it is fraced will tend to dissolve salts in the formation thus giving the recovered water very high salinity.
The retuning fluid is generally collected in pits that are lined with plastic. The pit is then pumped dry, and the water is usually either recycled for fracing additional wells or else trucked off site to a waste water disposal facility. The Pennsylvania Department of Environmental Protection has formed a partnership with the oil and gas industry to research and develop innovative new methods of recycling and treating flowback water.
Municipal sewage disposal plants were never designed to handle recovered drilling fluids or produced water, yet existing and planned treatment facilities are believed to be adequate at least for the current level of Marcellus shale drilling in Pennsylvania.
A large percentage of flowback water is reused before it is released back into the environment. Roughly 60% gets reused, and this percentage is increasing. Industry leader Range Resources reuses 100% of its flowback water. All flowback water is either reused or treated by the industry.
