Flowback water
From Wikimarcellus
| Revision as of 18:35, 11 April 2010 Tcopley (Talk | contribs) (A large percentage of flowback water is reused before it is released) ← Previous diff |
Current revision Tcopley (Talk | contribs) (fracturing fluid) |
||
| Line 1: | Line 1: | ||
| - | '''Flowback water''' (aka backflow water) from [[Hydro-fracturing|fracing]] oil and gas wells, that is, the fluid which returns to the surface, can be anywhere from 33 to 50 percent of the volume that is forced down a well. | + | [[Image:Jos4.gif|frame|right|<div align="center">Brine water tanks (collect residual frac water as it returns to the surface over time). [[EQT Corporation|EQT Corp.]] drilling site located near the Borough of Waynesburg in Greene Co., PA about 60 miles southwest of Pittsburgh. Photo credit [http://www.gomarcellusshale.com/profile/JosephineSabillon Josephine Sabillon].</div>]]''Flowback water'' (aka ''backflow water'') is the murky, salty water from [[Hydro-fracturing|fracing]] natural gas wells. It consists of [[Drilling fluid|frac fluid]] which returns to the surface (aka the ''frac load recovery'') as well as [[produced water]]. This water contains clay, dirt, metals, chemicals and even diesel that may have been added. |
| - | This flowback may be characterized as having high salinity and [[Total dissolved solids|total dissolved solids]] (TDS). It is laden with the same fracing chemicals that were pumped into the well, in addition to [[Produced water|unique contaminants]] that are present in the rock formation below. | + | The frac load recovery can be anywhere from 15-40% percent of the volume of fluid that is injected, that is forced down a well, and it flows back over a period of 3-4 weeks after fracing--most of it within 7 to 10 days. More than half of the frac fluid remains in the formation. At a certain point there is a transition between primarily recovering frac fluid to that of [[produced water]]. Usually this point is difficult to distinguish, yet may be discerned from the different chemical signatures of the frac water versus the naturally occurring water produced by the formation. A typical flowback of frac fluids might run 40,000 bbl. After the initial 3-4 week post-fracing recovery of fluids, an additional 10,000 to 30,000 bbl of produced water may flow for up to two years. |
| - | The retuning fluid is generally collected in pits that are lined with plastic. The pit is then pumped dry, and the water is usually either recycled for fracing additional wells or else trucked off site to a waste water disposal facility. The [[Pennsylvania Department of Environmental Protection]] has formed a partnership with the oil and gas industry to research and develop innovative new methods of recycling and treating flowback water. | + | Flowback water may be characterized as having high salinity and [[Total dissolved solids|total dissolved solids]] (TDS). It is laden with the same fracing chemicals that were pumped into the well, in addition to any [[Produced water|unique contaminants]] that are present in the rock formation water deep below. In addition to natural salinity of water in the formation, any fresh water that is forced down a well, when it is fraced, will tend to dissolve salts in the formation thus giving the recovered water very high salinity. |
| - | Municipal sewage disposal plants were never designed to handle flowback water, yet existing and planned treatment facilities are believed to be adequate at least for the current level of [[Marcellus shale]] drilling in [[Pennsylvania]]. | + | The retuning fluid is generally collected in metal tanks or else open pools, lagoons or pits lined with one or more layers of plastic. These are then pumped dry, and water is usually either recycled for fracing additional wells or else trucked off site to a waste water disposal facility. Containment pits, or open-air ponds that are lined with plastic, can become points of failure. Occasionally, liners get cracked or damaged. Contaminated fluids can then leach into ground water. |
| - | A large percentage of flowback water is reused before it is released back into the environment. Roughly 60% gets reused, and this percentage is increasing. Industry leader [[Range Resources]] reuses 100% of its flowback water. All flowback water is either reused or treated by the industry. | + | Increasingly, drillers are shifting to [[closed loop system]]s as the preferred method of handling flowback water. |
| + | |||
| + | The [[Pennsylvania Department of Environmental Protection]] has formed a partnership with the oil and gas industry to research and develop innovative new methods of recycling and treating flowback water. | ||
| + | |||
| + | Municipal sewage disposal plants were never designed to handle recovered fracturing fluids or produced water, yet existing and planned treatment facilities are believed to be adequate at least for the current level of [[Marcellus shale]] drilling in [[Pennsylvania]]. | ||
| + | |||
| + | A large percentage of flowback water is [[Closed loop system|reused]] before it is released back into the environment. Roughly 60% gets reused, and this percentage is increasing. When multiple wells are in close proximity to each other, recycling the water is more cost effective. The amount of iron in the water, suspended solids, bacteria and other contaminants also help determine whether reuse is a practical alternative. | ||
| + | |||
| + | Industry leader [[Range Resources]] reuses 100% of its flowback water. All flowback water is either reused or treated by the industry. | ||
| + | |||
| + | ===Resources=== | ||
| + | |||
| + | [http://www.governor.state.pa.us/portal/server.pt/community/marcellus_shale_wastewater_partnership/18683 Marcellus Shale Wastewater Partnership] | ||
| + | |||
| + | [[Category:Drilling practices]] | ||
Current revision
The frac load recovery can be anywhere from 15-40% percent of the volume of fluid that is injected, that is forced down a well, and it flows back over a period of 3-4 weeks after fracing--most of it within 7 to 10 days. More than half of the frac fluid remains in the formation. At a certain point there is a transition between primarily recovering frac fluid to that of produced water. Usually this point is difficult to distinguish, yet may be discerned from the different chemical signatures of the frac water versus the naturally occurring water produced by the formation. A typical flowback of frac fluids might run 40,000 bbl. After the initial 3-4 week post-fracing recovery of fluids, an additional 10,000 to 30,000 bbl of produced water may flow for up to two years.
Flowback water may be characterized as having high salinity and total dissolved solids (TDS). It is laden with the same fracing chemicals that were pumped into the well, in addition to any unique contaminants that are present in the rock formation water deep below. In addition to natural salinity of water in the formation, any fresh water that is forced down a well, when it is fraced, will tend to dissolve salts in the formation thus giving the recovered water very high salinity.
The retuning fluid is generally collected in metal tanks or else open pools, lagoons or pits lined with one or more layers of plastic. These are then pumped dry, and water is usually either recycled for fracing additional wells or else trucked off site to a waste water disposal facility. Containment pits, or open-air ponds that are lined with plastic, can become points of failure. Occasionally, liners get cracked or damaged. Contaminated fluids can then leach into ground water.
Increasingly, drillers are shifting to closed loop systems as the preferred method of handling flowback water.
The Pennsylvania Department of Environmental Protection has formed a partnership with the oil and gas industry to research and develop innovative new methods of recycling and treating flowback water.
Municipal sewage disposal plants were never designed to handle recovered fracturing fluids or produced water, yet existing and planned treatment facilities are believed to be adequate at least for the current level of Marcellus shale drilling in Pennsylvania.
A large percentage of flowback water is reused before it is released back into the environment. Roughly 60% gets reused, and this percentage is increasing. When multiple wells are in close proximity to each other, recycling the water is more cost effective. The amount of iron in the water, suspended solids, bacteria and other contaminants also help determine whether reuse is a practical alternative.
Industry leader Range Resources reuses 100% of its flowback water. All flowback water is either reused or treated by the industry.
